Calculator Guide
What size water softener do you need?
Multiply people by gallons per day by hardness, then by 7 days. Pick a softener whose usable capacity, not its label, covers the result. A family of 4 at 15 gpg lands on 48,000 to 64,000 grains.
The formula in three steps
- Daily grains. People x gallons per person per day x hardness in grains per gallon (gpg). We assume 75 gallons per person, the industry sizing convention, unless you change it. Outdoor taps usually bypass the softener, which is why this is lower than total household use.
- Capacity needed. Daily grains x 7. That targets a regeneration about once a week, the usual goal for a metered softener.
- Pick a size. The smallest standard softener whose usable capacity at an efficient salt setting is at least that number.
Worked example: a family of 4
4 people x 75 gallons x 15 gpg = 4,500 grains a day. Multiply by 7days and you need 31,500 grains of usable capacity between regenerations.
Here's the catch. A softener's rating assumes a heavy salt dose. Set to an efficient 6 lb of salt per cubic foot of resin, it delivers only about 62.5% to 75% of the rating, depending on whose figures you use. A 48,000-grain unit gives 30,000 to 36,000 usable grains. The top of that range covers 31,500; the bottom doesn't. That's why we recommend 48,000 to 64,000 grains. Pick the larger size if you want to be sure of low salt use.
| Rated size | Resin | Usable at efficient salt setting |
|---|---|---|
| 24,000 grain | 0.75 cu ft | 15,000 to 18,000 |
| 32,000 grain | 1 cu ft | 20,000 to 24,000 |
| 40,000 grain | 1.25 cu ft | 25,000 to 30,000 |
| 48,000 grain | 1.5 cu ft | 30,000 to 36,000 |
| 64,000 grain | 2 cu ft | 40,000 to 48,000 |
| 80,000 grain | 2.5 cu ft | 50,000 to 60,000 |
| 96,000 grain | 3 cu ft | 60,000 to 72,000 |
You could buy a smaller unit and run it at the high salt setting. It would soften the water, but it would use more salt every week for as long as you own it.
Sizing chart
Recommended size by household and hardness, at 75 gallons per person per day and no iron. Where two sizes are shown, the smaller works at a moderately efficient setting and the larger at the most efficient one.
| People | 5 gpg | 10 gpg | 15 gpg | 20 gpg | 25 gpg |
|---|---|---|---|---|---|
| 1 | 24k | 24k | 24k | 24k | 24k |
| 2 | 24k | 24k | 24k to 32k | 32k to 40k | 40k to 48k |
| 3 | 24k | 24k to 32k | 32k to 40k | 48k to 64k | 64k |
| 4 | 24k | 32k to 40k | 48k to 64k | 64k to 80k | 80k to 96k |
| 5 | 24k | 40k to 48k | 64k | 80k to 96k | 96k* |
| 6 | 24k to 32k | 48k to 64k | 64k to 80k | 96k* | 96k* |
* More than the largest standard single tank (96,000 grains) handles at an efficient setting. Consider a twin-tank system, which costs about $1,200 to $3,000 for the unit.
One salt-based softener sold in four of the sizes in this chart is below. We list it for its range of sizes; we haven't tested it. Check your size against the chart before you order.
Disclosure: this page contains affiliate links, marked "Check price". If you buy through them we may earn a commission at no extra cost to you. It never changes our numbers. How we make money
SoftPro Elite HE water softener
Sold in 32,000, 40,000, 48,000 and 64,000-grain sizes. Pick the size from the chart above.
Things that change the answer
Your real water use
75 gallons per person per day is a planning number. Homes with efficient fixtures use less; homes with frequent guests or long showers use more. If you know your use from a water bill, divide monthly gallons by 30 and by the number of people, subtract a bit for outdoor watering, and enter it under "Refine" in the calculator.
Iron
Iron fouls resin and uses capacity. We add 3 to 5 gpg of effective hardness per ppm of iron. With 1 ppm, our family of 4 would need 37,800 to 42,000 grains between regenerations, which points to a 64,000 to 80,000-grain unit. Most softeners are rated for only a few ppm of clear-water iron, and rusty (oxidized) iron clogs resin. Above 3 ppm, a dedicated iron filter is usually the better fix.
Flow rate
Capacity is about how much hardness the softener holds. Flow rate is how much water it can pass at once without pressure dropping. Larger homes with several bathrooms running at once may need a unit rated for higher flow even if their hardness math points to a modest size. Check the rated service flow in gallons per minute.
Hardness you don't know yet
Our ZIP lookup gives a starting point, but hardness varies across a city and can change with the season. Your utility's water quality report or a test kit is more accurate. See how to find your hardness.
Common questions
- What size water softener do I need for a family of 4?
- At 15 grains per gallon and 75 gallons per person per day, a family of 4 removes 4,500 grains a day. A weekly regeneration needs 31,500 grains of usable capacity, which points to a 48,000 to 64,000-grain softener depending on how efficiently it is set up. The larger size is the safe choice if you want to run a low salt setting.
- Is it bad to oversize a water softener?
- One size up is fine and gives you room for guests or a growing family. Going far beyond your needs costs more up front for no benefit. Aim for a regeneration about once a week.
- Why does the recommended size look bigger than the math suggests?
- Ratings like "48,000 grains" assume a heavy salt dose of roughly 15 to 18 lb per cubic foot of resin. At an efficient setting, a softener delivers about 62.5% to 75% of its rating. We size against that usable capacity, which saves salt over the life of the unit.
- How does iron affect softener size?
- Iron uses up softener capacity too. Rules of thumb add 3 to 5 gpg of effective hardness for every 1 ppm of iron, and there's no official standard. Above 3 ppm, a separate iron filter usually makes more sense than a bigger softener.
Numbers on this page come from our cost inputs and sources, last reviewed 2026-11.