Skip to contentSoftenerMath

Calculator Guide

Water softeners for well water

On a private well, nobody publishes a water report for you, and iron changes the size you need. Test first, then size for hardness plus iron. A family of 4 at 15 gpg with no iron needs about a 48,000 to 64,000-grain softener.

Test your well first

Private wells aren't covered by the federal Safe Drinking Water Act, and most states don't regulate them either. The owner is responsible for the water, according to the EPA. So unlike city water, there's no report to look up.

For a softener you need three numbers: hardness, iron and pH. A home test kit gives hardness and iron in minutes. A certified lab test costs more but also checks bacteria, nitrates and metals, which matter more for your health than hardness does. If you've never tested your well, do the lab test for its own sake.

How iron changes the size you need

A softener's resin removes dissolved iron the same way it removes calcium and magnesium, and iron uses up capacity faster. Sizing guides add 3 to 5 grains per gallon for each ppm of iron. They don't agree on one number, so we show the range.

For a family of 4 using 75 gallons each a day at 15 gpg:

IronEffective hardnessRecommended size10-year total
0 ppm15 gpg48,000 to 64,000 grains$1,550 to $8,520
1 ppm18 to 20 gpg64,000 to 80,000 grains$1,900 to $9,430
2 ppm21 to 25 gpg64,000 to 96,000 grains$2,000 to $10,040
3 ppm24 to 30 gpg80,000 to 96,000 grains$2,860 to $10,450

When you need an iron filter too

  • Above about 3 ppm of iron, we suggest a dedicated iron filter ahead of the softener. Published limits for a softener alone run from about 2 to 10 ppm, so 3 ppm is a middle value.
  • Red or orange water means the iron has already rusted. That kind clogs softener resin and should be filtered out first, according to Penn State Extension.
  • Stains start low. EPA's secondary (staining) level for iron is 0.3 ppm, so even a little iron can mark sinks and laundry. That's also the amount our calculator assumes for a well until you enter your own.

What it costs to run on a well

Each regeneration flushes water down the drain. On city water you pay for it twice, as water and as sewer. On a well you don't, so the yearly cost is a little lower. For a family of 4 at 15 gpg with no iron:

Regeneration waterTotal per year
City water$27 to $45$95 to $560
Well$0$68 to $510

Iron raises the cost a different way: a bigger softener, more salt and, above about 3 ppm, a separate filter. The calculator includes the first two. Our methodology page lists every input.

Common questions

Do I need to test my well before buying a softener?
Yes. No utility tests a private well for you, and the right size depends on both hardness and iron. A test for hardness, iron and pH tells you what to buy. Until you have one, our calculator assumes 0.3 ppm of iron for a well.
Can a water softener remove iron?
Some, if it is clear-water (dissolved) iron at low levels. Sources disagree on the limit, and we suggest a separate iron filter above about 3 ppm. Red, already-rusted iron clogs the resin and should be filtered out first.
How does iron change the softener size?
Each ppm of iron counts as about 3 to 5 extra grains per gallon of hardness. For a family of 4 at 15 gpg, 3 ppm of iron moves the recommendation from 48,000 grains up to as much as 96,000.
Is a softener cheaper to run on a well?
A little. You don't pay a water or sewer bill for the water the softener uses to regenerate. Salt, upkeep and resin cost the same as on city water.

Numbers on this page come from our cost inputs and sources, last reviewed 2026-11.